Comments on: FTM Pumping Primer

By: Mark

Mark — Tue, 20 Dec 2011 08:35:23 +0000

Just put a piece of tape over the hole, and pull it back when you want release, why keep your finger on the hole till your done.

By: Robert

Robert — Wed, 05 Oct 2011 23:11:46 +0000

I just recieved my pump in the mail today and was very excited. I just want to warn you guys about EXCITINGTOYS.COM They sell pumps but it takes then 2-3 months to send your purchase to you. They are on ripoffs.com so just watch out for this site. So after 2 months of waiting and complaining it finally arrived in the mail. So today is my happy pump day.

By: Jasen

Jasen — Tue, 13 Sep 2011 00:50:11 +0000

Thanks for this helpful guide! I was browsing the PumpToys website and found that they seem to have recently started selling FtM-specific cylinders; they call them TSP pre and post-op cylinders. They seem a bit expensive, so I was wondering if anyone has tried them and how well they worked. I like the look of the stepped entry cylinder even though I am pre-op; the flared ones always end up pinching and not sealing right for me.

By: Seti

Seti — Mon, 18 Jul 2011 15:13:11 +0000

@Chili: I don’t know if your question has been answered yet or if you found a suitable solution.

If you mean a DIY pump out of a syringe then just insert the plunger into the other end of the syringe’s barrel (that is, the end which you cut off). That way the rough edges won’t even touch your skin. Alternatively, use very fine sandpaper. Or try melting the cut edges carefully over a candle so that they get smoother. But don’t hold the pump too close to the flame. Keeping a good distance and proceeding slowly gives better results – you just want to melt the plastic a bit, not burn it.

By: Mitchell

Mitchell — Mon, 16 May 2011 01:29:58 +0000

hey guys,

i have been pumping and i think it has been affective but im not sure it might just be the testosterone but what is a good pressure to be at and how long do i need to do it for in sessions? and how many sessions a day would be good? i want to make sure i get the maximum penis size! please let me know!

By: Chili

Chili — Fri, 06 May 2011 14:25:25 +0000

Hello there! I made a homemade pump just the same as in the video above. I cut the top and rasped the edges to make them smooth, but I feel uncomfortable sharpness and pressure in my labia minora while pumping. What should I do, how should I make the edges less sharp?? I am considering to cover them with some kind of gum, but don’t know what to take…

By: Broken Dick

Broken Dick — Sun, 01 May 2011 06:49:48 +0000

I’ve been pumping for years and the other night a blood vessel burst, filling my cylinder (1 inch by 4 inch?) with blood. It was enough to make me rethink pumping. My gauge doesn’t have pounds on it for the pressure, just MM Hg in vac and inches of Hg in vac. Just did a quick conversion and 5 psi would be too much for me. 3.5 is do-able.

By: daniel

daniel — Tue, 14 Dec 2010 19:18:39 +0000

the 5 star pump you have advertised on here as high quality is pretty crappy actually. they just sent me a second broken one. i’m going to try to return it now.

By: Joshua

Joshua — Sat, 11 Dec 2010 01:41:26 +0000

@Taylor Check out the 3 Cylinder Set here. The large cylinder is 3.825" long and 1.125" in diameter Just $28 for the set. Close enough?

By: Taylor

Taylor — Thu, 09 Dec 2010 20:40:42 +0000

I was wondering if anyone knew where to find something close to 3” long and 1” in diameter. I know pumptoys sells custom cylinders, but I’m not trying to spend $110 on one just to start out. Any help is appreciated!